1、送電。合上控制柜內空氣開關，分條機電源指示燈亮，注意手指不能碰到接線端子，小心觸電，危及安全。
1. Power transmission. Close the air switch in the control cabinet, the power indicator light of the stripper will be on, pay attention not to touch the terminal with fingers, be careful of electric shock, which may endanger safety.
2、上簾布卷。打開導開安全卡頭，吊上簾布卷，合上安全卡頭，分離簾布和膠布，把簾布纏繞到收卷布筒上。橡膠托輥 槽型托輥 皮帶托輥 平行托輥 保定搬家 保定搬家電話 保定搬家公司 保定搬家 銅鼎 銅獅子
2. Upper cord roll. Open and open the safety clip, hang up the cord fabric reel, close the safety clip, separate the cord fabric and the adhesive tape, and wind the cord fabric onto the take-up drum.
3、人工傳膠布。導開打到手動，正轉點動導開 ，人工拖著膠布，穿過糾偏輥，張緊輥，剎車輥，驅動輥。
3. Manual tape transfer. Turn the guide to manual, turn forward and move the guide, manually drag the adhesive tape, pass through the correction roll, tension roll, brake roll and drive roll.
4、抽線。根據要生產膠條尺寸用剪刀剪開膠條，然后抽線，并固定在抽線輥上。
4. Draw line. According to the size of the rubber strip to be produced, use scissors to cut the rubber strip, then draw and fix it on the drawing roller.
5、上卷曲輥。卸下卷取軸頭端方軸，裝上30個尼龍卷軸，再裝上方軸，打開卷取安全卡頭，裝上卷取軸，卷取1和卷取2操作一樣。
5. Upper winding roller. Remove the square shaft at the end of the coiling shaft head, install 30 nylon reels, then install the upper shaft, open the coiling safety clip, and install the coiling shaft. Coiling 1 and coiling 2 operate the same.
6、上膠布頭。把膠條拉伸到合適位置，把膠條纏繞到卷軸上，注意膠條長度要保持一致，來保持膠條張力一致。
6. Glue the cloth head. Stretch the adhesive tape to the right position, wind the adhesive tape on the reel, and pay attention to the consistent length of the adhesive tape to keep the consistent tension of the adhesive tape.
7、調節張力。調節卷取張力到6.5-10之間，把導開張力調節到10-15之間，注意隨著卷取直徑加大，卷曲張力適當增加，保證膠條張力一致。
7. Adjust the tension. Adjust the coiling tension to 6.5-10, and the guide tension to 10-15. Pay attention to the appropriate increase of coiling tension with the increase of coiling diameter to ensure the consistent strip tension.
8、調節卷取速度。調節卷取速度在需要范圍內，注意啟動時卷取速度不能太大，以免糾偏跟蹤錯誤，可以調節到20啟動后再增速。
8. Adjust the coiling speed. Adjust the coiling speed within the required range. Pay attention to that the coiling speed should not be too large when starting, so as to avoid deviation correction and tracking error. The coiling speed can be adjusted to 20 and then increased after starting.
9、啟動機器。上述操作完成后，按啟動按鈕，轉動一兩圈后，觀察卷軸膠條是否有偏移不正狀態，若有，停止卷取，擺正位置，再繼續旋轉。同時注意抽線線頭位置，來調節抽線啟停，防止線頭拉斷或夾線。
9. Start the machine. After the above operation is completed, press the start button and rotate it for one or two circles to observe whether the rubber strip of the reel is deviated. If so, stop coiling, put it in the right position, and then continue to rotate. At the same time, pay attention to